APRS Track Direct

My position About ☰

reset

SP2WM-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2WM-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1765727431	26 Count	0 Count	0 Count
1765719322	17 Count	0 Count	0 Count
1765713917	11 Count	0 Count	0 Count
1765708530	1 Count	0 Count	0 Count
1765707630	0 Count	0 Count	0 Count
1765706729	1000 Count	140 Count	139 Count
1765705828	999 Count	140 Count	139 Count
1765703126	996 Count	140 Count	139 Count
1765701324	994 Count	140 Count	139 Count
1765696820	989 Count	140 Count	139 Count
1765695920	988 Count	140 Count	139 Count
1765694119	986 Count	140 Count	139 Count
1765691416	983 Count	140 Count	139 Count
1765690515	982 Count	140 Count	139 Count
1765689614	981 Count	140 Count	139 Count
1765688713	980 Count	140 Count	139 Count
1765687813	979 Count	140 Count	139 Count
1765686930	974 Count	140 Count	139 Count
1765686029	973 Count	140 Count	139 Count
1765685128	972 Count	140 Count	139 Count
1765684227	971 Count	140 Count	139 Count
1765679723	966 Count	140 Count	139 Count
1765675219	961 Count	140 Count	139 Count
1765656321	936 Count	140 Count	139 Count
1765655420	935 Count	140 Count	139 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: