APRS Track Direct

My position About ☰

reset

SQ4HSE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ4HSE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1766429983	6 Count	39 Count	5 Count
1766422781	157 Count	1021 Count	113 Count
1766408376	139 Count	925 Count	99 Count
1766404775	134 Count	903 Count	95 Count
1766401174	130 Count	878 Count	92 Count
1766399292	129 Count	878 Count	92 Count
1766395688	126 Count	857 Count	90 Count
1766392086	123 Count	836 Count	88 Count
1766388485	120 Count	814 Count	86 Count
1766384884	116 Count	790 Count	83 Count
1766381284	111 Count	765 Count	79 Count
1766377682	107 Count	744 Count	76 Count
1766374082	102 Count	722 Count	72 Count
1766370481	97 Count	697 Count	68 Count
1766366880	93 Count	673 Count	65 Count
1766363279	90 Count	653 Count	63 Count
1766356077	84 Count	610 Count	59 Count
1766352476	80 Count	587 Count	56 Count
1766348875	76 Count	568 Count	53 Count
1766334471	64 Count	476 Count	45 Count
1766330870	60 Count	454 Count	42 Count
1766327270	57 Count	433 Count	40 Count
1766323668	53 Count	411 Count	37 Count
1766320067	50 Count	388 Count	35 Count
1766316466	47 Count	365 Count	33 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: