APRS Track Direct

My position About ☰

reset

UN1GWA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UN1GWA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1758169906	245 Count	426 Count	164 Count
1758169004	242 Count	420 Count	162 Count
1758168098	239 Count	414 Count	160 Count
1758167189	236 Count	407 Count	158 Count
1758166283	233 Count	401 Count	156 Count
1758165377	230 Count	395 Count	154 Count
1758164472	227 Count	390 Count	152 Count
1758163566	224 Count	385 Count	150 Count
1758162661	221 Count	379 Count	148 Count
1758141965	152 Count	237 Count	102 Count
1758141060	149 Count	230 Count	100 Count
1758140154	146 Count	223 Count	98 Count
1758139248	143 Count	218 Count	96 Count
1758137437	137 Count	206 Count	92 Count
1758136531	134 Count	199 Count	90 Count
1758135626	131 Count	194 Count	88 Count
1758134720	128 Count	187 Count	86 Count
1758133815	125 Count	181 Count	84 Count
1758133045	122 Count	175 Count	82 Count
1758132150	119 Count	167 Count	80 Count
1758131233	116 Count	162 Count	78 Count
1758130327	113 Count	155 Count	76 Count
1758129421	110 Count	152 Count	74 Count
1758128516	107 Count	150 Count	72 Count
1758127610	104 Count	146 Count	70 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: